Nano Tube Aerator Fine Bubble Air Diffuser For Industrial Water Treatment
Product Description
The fine bubble tube diffuser is a new type of oxygenation aerator and the core equipment of A/O process (activated sludge biochemistry technology). It can be applied to every position of the sewage pool. It is featured by easy and convenient installation and maintenance, even oxygenation and low energy consumption.
Product Feature
1. Digital control knife
Membrane has large numbers of self-closing holes with using mechanical punching technology. The holes can automatically open and close when the oxygen operation stopped, so it can avoid blocking holes;When aeration tank stops, sewage mixing will not be poured back, also can reduce maintenance.
2. Environmental material
Use engineering plastics ABS material, simple structure, reliable performance, hollow water filling, greatly reducing the buoyancy of the aeration system in the water.
3. High opening rate
Membrane is installed conveniently and uniformly arrangement, so that air can arrange the whole membrane evenly, and the opening rate will increase. Thus the aeration capacity and service area will increase, and aeration resistance is reduced when the aerator starts.
Product Application
Our products are mainly applied in wastewater treatment of city planning, textile printing , pharmacy, petrochemical engineering ,charking,process hides, make mine and aquiculture.
Technology Parameter
| Item | φ65*500mm | φ65*750mm | φ65*1000mm |
| Spec. φ*L mm | 65*500mm | 65*750mm | 65*1000mm |
| Oxygen transfer efficiency | Water Depth 5m | 23-32% |
| Water Depth 6m | 34-39.5% |
| Water Depth 7m | 31-45% |
| Ventilatory volume (m3/h) | 1.7-6.8 | 3.4-13.6 | 3.4-17 |
| Service area | 0.82-1.26m2 | 0.98-2.11m2 | 0.98-2.35m2 |
| Number of holes | 8080 | 10300 | 13880 |
| Bubble diameter | 0.8-2.0mm |
| Pressure loss | 25-42cm | 25-41.5cm | 25-40cm |
| Oxygenation capacity | Micropore: 7.5kgO2/kw.h(under 5m of water); Pore:3.5-4.8kgO2/kw.h(under 5m of water) |
| Extension ability | >600% |
| Tension strength | >13.8*103kpa |
Product Maintance
1. The operator should always check the aeration status of the aeration system. If the resistance of the aeration system increases in the head or the shape of the bubbles changes, the aerator needs to clean up such as carbonates, iron salts, aluminum salts and biological sludge Such as sedimentation, scaling on the rubber membrane of the aerator will lead to a reduction in the air output, the oxygen utilization law of the aeration system will decrease, and the head loss will increase.
2. Periodic drainage cleaning is the ideal maintenance method, and the length of the period depends on the nature of the treated water, the treatment process and other factors.
3. Pay attention not to let the sediment on the surface of the rubber film dry and agglomerate during the drainage cleaning and maintenance, and it needs to be cleaned immediately. The dry agglomerates of the deposits will make cleaning work difficult, thereby affecting the performance of the aerator.
4. Biological sludge can be removed by physical methods. Use a brush to clean the surface of the rubber membrane or rinse it with a high-pressure water gun. When cleaning with a high-pressure water gun, keep the nozzle of the water gun at a distance of approximately 500 mm from the surface of the rubber film to prevent damage to the rubber film.
5. Scales such as carbonates should be removed chemically. A certain amount of formic acid enters the aeration system with air. The proportion of formic acid added depends on the degree of scaling. It is not necessary to empty the water in the aeration tank when cleaning. . Generally, it is cleaned once or twice a year.
6. When the microporous aerator is damaged or the performance requirements are not met after cleaning and maintenance, the rubber diaphragm or the entire aerator can be replaced. The replacement method is the same as the installation method.
Product Tags:
|
|
Nano Tube Aerator Fine Air Bubble Diffuser For Industrial Water Treatment Images
|
